Locate Brownells 3 Flute Carbide Drill Brownells Gunsmith Tools Supplies

Brownells 3 Flute Carbide Drill Brownells Gunsmith Tools Supplies

Brownells 3 Flute Carbide Drill Brownells Gunsmith Tools Supplies

Top Rated Brownells 3 Flute Carbide Drill Brownells Gunsmith Tools Supplies
Customers Top Rated Product!

Retail Price: $18.99

Add to Cart




Three-flute design spreads cutting loads over a larger area so holes are cleaner and rounder. The bit itself will last longer too. Designed for cutting hard metals: stainless nickel steel alloys titanium plus great on soft metals too. Mfg: Brownells SPECS: #28 .1405 (3.6mm) dia. 1-7/8 (4.8cm) long. #29 .1360 (3.45mm) dia. 2 (4.8cm) long. #31 .120 (3mm) dia. 1-15/16 (4.9cm) long. #33 .1130 (2.87mm) dia. 1-7/8 (4.8cm) long..
Brownells 3 Flute Carbide Drill Brownells Gunsmith Tools Supplies
Product Number: Power Tools & Accessories
Brand: Brownells
Category: Gunsmith Tools & Supplies

More Information on Brownells 3 Flute Carbide Drill Brownells Gunsmith Tools Supplies






Products Other People Bought Brownells 3 Flute Carbide Drill Brownells Gunsmith Tools Supplies

Brownells Solid Carbide Drill Brownells Gunsmith Tools Supplies

Brownells Solid Carbide Drill Brownells Gunsmith Tools Supplies

Customer Rating For Brownells Solid Carbide Drill Brownells Gunsmith Tools Supplies

Specially ground single-flute solid carbide drills ideally suited for use by the professional gun trade on hard receivers (as the 03A3 and harder). * Cuts a clean chip in hardest file steel giving true hole. * Does not crumble out the steel; thus no chatter. * 2 long to give quill clearance when using with Forster and other scope/sight mounting jigs. * Kept properly cleaned will not bind or break. * Properly fed wont work-harden hole surface like spade drill does; decreases tap breakage. * Drills all the way through hardened steels. Note: Common sense must be used. No guarantee against breakage! Use only to crack the skin Mfg: Brownells SPECS: Sizes available: No. 56 (0-80) No. 50 (2-56) No. 38 (5-40) No. 36 (6-32 No. 33 (6-40) No. 31 (6-48) No. 29 (8-32) No. 28 (8-40). Speed approximately twice that of high speed steel feed rate the same or slightly less.

Retail Price: $28.99

More Information about Brownells Solid Carbide Drill Brownells Gunsmith Tools Supplies

Brownells Carbide Center Drill Brownells Gunsmith Tools Supplies

Brownells Carbide Center Drill Brownells Gunsmith Tools Supplies

Customer Rating For Brownells Carbide Center Drill Brownells Gunsmith Tools Supplies

If none of the common methods for removing a frozen screw work and drilling is in order these carbide center drills should be used to center and start the hole. With the spindle at fairly high speed bring the center drill down to the screw head and adjust position until centered in the screw. Apply pressure and cut until center hole is deep enough to allow the proper undersized regular drill bit to start cutting without catching on the screw head slot. Better for drilling broken taps too for they will cut center holes in even the hardest ones. And because of the large body mass of the tool relative to the small drill diameter it is very sturdy and rigid. Mfg: Brownells SPECS: #1 .125 body/.0468 drill; #2 .187 body/.0781 drill; #3 .250 body/.1093 drill; #4 .312 body/.1250 drill.

Retail Price: $20.99

More Information about Brownells Carbide Center Drill Brownells Gunsmith Tools Supplies

Brownells 22 Cal 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

Brownells 22 Cal 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

Customer Rating For Brownells 22 Cal 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

A ready-to-use combination of twelve-flute cutter and brass pilot for touching up those minor rifle muzzle imperfections that can destroy fine accuracy. Twelve flutes cut smooth and chatter free so no stoning lapping or touch up is required. Hardened brass pilots wont scar or damage delicate rifling. A very handy tool to take along to the range or keep in your tool box just in case . Mfg: Brownells SPECS: Cutter - tool steel 3 1/4 (8.2cm) long. Handle - aluminum 3 1/2 (8.8cm) long. Pilot - brass 1 1/4 (3cm) long. One Caliber Set includes cutter pilot and handle.

Retail Price: $95.99

More Information about Brownells 22 Cal 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

Brownells 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

Brownells 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

Customer Rating For Brownells 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

A ready-to-use combination of twelve-flute cutter and brass pilot for touching up those minor rifle muzzle imperfections that can destroy fine accuracy. Twelve flutes cut smooth and chatter free so no stoning lapping or touch up is required. Hardened brass pilots wont scar or damage delicate rifling. A very handy tool to take along to the range or keep in your tool box just in case . Mfg: Brownells SPECS: One Caliber Set includes cutter pilot and handle.

Retail Price: $79.97

More Information about Brownells 12 Flute Muzzle Chamfer Set Brownells Gunsmith Tools Supplies

Brownells Spiral Flute Long Forcing Cone Reamer Brownells Gunsmith Tools Supplies

Brownells Spiral Flute Long Forcing Cone Reamer Brownells Gunsmith Tools Supplies

Customer Rating For Brownells Spiral Flute Long Forcing Cone Reamer Brownells Gunsmith Tools Supplies

Lengthening the forcing cone area decreases pellet deformation and felt recoil for a dramatic improvement in pattern density shooting comfort and overall shotgun performance. Custom-made reamers with five spiral flutes increase the cutting surface area for a smooth chatter-free cut on all types of barrel steel. Do not use on chrome lined bores. Hex-drive shank allows the use of a standard square drive socket and T-handle. Mfg: Brownells SPECS: Tool steel five flute spiral cut 6 (15cm) long 1 (2.5cm) long hex section. Hex-drive size listed in chart.

Retail Price: $129.99

More Information about Brownells Spiral Flute Long Forcing Cone Reamer Brownells Gunsmith Tools Supplies

Brownells Silicon Carbide Abrasive Grit Brownells Gunsmith Tools Supplies

Brownells Silicon Carbide Abrasive Grit Brownells Gunsmith Tools Supplies

Customer Rating For Brownells Silicon Carbide Abrasive Grit Brownells Gunsmith Tools Supplies

Very fine abrasive powders you can use to rub in parts. Make an abrasive/cutting-oil paste for metal work or use dry on a soft pad to bring a cured stock finish to a gloss. Follow with Brownells Stock Rubbing Compound. Mfg: Brownells SPECS:120 grit (coarse); 600 grit (fine). 1 lb. net wt. in plastic jar.

Retail Price: $24.99

More Information about Brownells Silicon Carbide Abrasive Grit Brownells Gunsmith Tools Supplies

Brownells Silicon Carbide Abrasive Compound Brownells Gunsmith Tools Supplies

Brownells Silicon Carbide Abrasive Compound Brownells Gunsmith Tools Supplies

Customer Rating For Brownells Silicon Carbide Abrasive Compound Brownells Gunsmith Tools Supplies

The very best abrasive compound for hard fitting two pieces of steel. Stands up to continued fitting even on hardened and heat-treated steel. Silicon carbide grit combined with a thick long lasting lubricant breaks down into smaller and smaller sharp-edged particles to keep cutting longer than aluminum oxide compounds. For use on steel only. Remove with solvent. Mfg: Brownells SPECS: 4 fl. oz. (118 ml).

Retail Price: $16.99

More Information about Brownells Silicon Carbide Abrasive Compound Brownells Gunsmith Tools Supplies

Brownells Carbide Sight Insert Cutter Brownells Gunsmith Tools Supplies

Brownells Carbide Sight Insert Cutter Brownells Gunsmith Tools Supplies

Customer Rating For Brownells Carbide Sight Insert Cutter Brownells Gunsmith Tools Supplies

Weve had many requests for a small dovetail cutter that would speed up the cutting of dovetails in front sight blades when installing colored inserts. The one weve had made cuts a 1/4 wide dovetail just right for sight inserts and the finished product is very precise. Since the cutter is small (it tapers to a diameter of .110 ) you must make an initial cut with a 1/8 end mill (listed below). By using the end mill to remove some metal first youll avoid overloading the cutter and breaking it. CAUTION: For use in milling machine only. Solid carbide 2 (5cm) long. 1/4 (6.3cm) diameter shank. 60deg shoulder. Mfg: Brownells

Retail Price: $65.99

More Information about Brownells Carbide Sight Insert Cutter Brownells Gunsmith Tools Supplies